SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.
Direction
1. Wash car, removing sand and dust from the body of vehicle.
2. Knead clay bar by hand until it's soft and flat.
3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.
Direction
1. Wash off sand, mud or dust prior to spraying.
2. Shake bottle well approx. 20 times, and turn trigger "ON".
3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.
4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.
* When spray over brake disc, it reacts and changes colour.
Rinse away immediately, if left on too long, may cause bad effects for brake disc.
5. Wipe off with clean towel.
Carry out brake test with low gear 2-3 times after cleaning.
* This product is formulated for wheel.
If use for car body, carefully rinse off with water afterwards.
Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!
✔ Oil, Polish residue and fillers remover ✔ Prep item before applying wax / coating ✔ Replaces IPA wipe down ✔ Improves the adhesion of the surface protective coating ✔ Safe for paint
Direction
1. Shake bottle well
2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth
3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.
Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.
Direction
1. Wash car to remove sand or dust.
2. Knead clay bar by hand until it's soft and flat.
3. Rub lightly on car surface and wet area being cleaned.
4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
✔ QUICK EASY CLEAN & WAX CAR ✔ NO RINSING OR DRYING REQUIRED ✔ WATER REPELLENCY UP TO 1 MONTH ✔ CAN BE USE ON CERAMIC COATED VEHICLES
Triple-layer sheet for easy washing and waxing. Central layer designed for absorbing dirt to keep the outer layers clean. Helps prevent scratches and supports the structure of the outer layers to glide lightly and effortlessly over your vehicle. Leaves your car clean, shiny and with water repellency up to 1 months.
Direction
1. Open the front flap, and pull out one wipe.
2. Fold the sheet into quarters and lightly wipe down the body of the vehicle. Keep refolding the wipe to expose fresh surfaces and avoid spreading any dirt.
3. In particularly dirty areas, gently wipe off the dirt, then with a fresh surface of the sheet wipe of again.
4. If the entire wipe is dirty or becomes dried out, please use a fresh sheet.
Just spray on and wipe off to remove dead bugs, tar, and other oily dirt. It really is that so simple! It also creates a temporary anti-fouling coating to prevent adhesion of dirt.
Direction
* Use on a washed and dried vehicle.
1. Spray on the dirty area from a distance of 20-30 cm.
Contents - Cleaner (120mL) x 1bottle, Brush x 1pc, Cup x 1pc, Gloves x 2pcs
Features
This is acid type wheel cleaner, can dissolve burned iron powder and brake dust which cannot remove by conventional wheel cleaner with easy procedure. Strong acid cleaner dissolves heavy iron powder, which stuck against wheel, without damaged paint surface.
Direction
1. Remove dirt or oil by car shampoo and wipe off thoroughly.
2. Be sure that wheel is cool and confirm the area where iron powder is accumulated.
3. Take moderate amount of solution into attached cup, and start applying accumulated area with brush.
4. Let sit 10 minutes, buff off with clean towel. In case of difficultly wiping off once, repeat procedure 3 and 4.
* Application is up to 3 times.
5. Afterwards remove residue by rubbing with water.
* If rinsing is not enough, wheel might discolour, blushing and cause stain.
Cleaner design for glass/ceramic coating contains only mild cleaning ingredients. Restoring brightness of coated vehicle body. Symptoms such as water spots, small scratches on door knobs can be easily removed!
Direction
1. Wash off dirt, dust or mud, and wipe off water.
2. Shake bottle well.
3. Pour a coin size amount of liquid onto included towel.
4. Rub towel onto surface one panel at a time on affected areas.
Dead bugs, bird droppings and tree sap can cause damage to car paint. Not with FUKUPIKA Bugs& Droppings Removal, simply just wiping, removes and completely cleans the car's surface. Compared with conventional cleaning wipes, this wipe makes it possible give the car a nice clean surface finish, without leaving behind any white residue. The products does not contain any petroleum solvent, making FUKUPIKA absolutely eco-friendly!
Direction
1. Take out one sheet from package.
2. Do not rub with excessive force. If removing heavy dirt, wipe and allow cleaner to penetrate dirt, then gently wipe area. Results may vary depending on the contamination and adhesion of dirt.
3. When removing mud, sand, and dust, wipe off surface lightly and finish with a cleaner side of wipe. * If white residue of cleaner remains on surface, wipe off with a clean wet towel.
4. If whole sheet gets dirty or dry, use another sheet. * Seal package firmly, in order to prevent sheets from drying out.
With Stain Cleaner Strong Type, all you need to do is spray and wipe it off. The white powder won't remain on the surface and re-wiping is NOT necessary. It chemically breaks down and gets rid of stubborn dirt, which normal car shampoo couldn't do. Abrasive compounds are NOT included, so it won't damage your car paint. The fresh scent of grapefruit gets rid off bad odor during the process.
Direction
* Remove dirt from the car in advance.
1. Shake the bottle well.
2. Turn the nozzle to <ON>, and spray it on the surface.
Liquid penetrates effectively between the space of adhesive and bonded surface allowed easy removal of sticky adhesive residues.
Direction
* Cut the end of a nozzle into the desired size.
1. Shear off the edge of a sticker and spray into gap with a small amount of liquid. Then, using the included spatula rub the sticker until it goes off.
2. In case any glue residue still remains on the surface, it's best to spray it again and let it soak for a while. Then, using a soft cloth try to rub it off. If the glue residue remains on the surface repeat process until completely removed.
pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.
Direction
1. Wash off sand, mud or dust prior to spraying.
2. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.
3. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.
* When spray over brake disc, it reacts and changes colour.
Rinse away immediately, if left on too long, may cause bad effects for brake disc.
4. Wipe off with clean towel.
Carry out brake test with low gear 2-3 times after cleaning.
* This product is formulated for wheel.
If use for car body, carefully rinse off with water afterwards.
