Combining the abrasive powder of small, hard particles and big, soft particles, Glaco Glass Compound Roll-On is able to remove the toughest stains made from oily dirt and fluorine film. By just applying the product lightly onto the glass you will see immediate results as the roll-on removes the oil-film with ease. This convenient product can be used as surface preparation just before applying any coating to the glass.
Direction
1. Remove dust and dirt from glass with water, wipe off any water drops remaining on surface.
2. Shake bottle well with cap on and remove plastic seal.
3. Squeeze handle part of bottle to release compound liquid.
4.Polish onto glass until surface stops repelling liquid.
5. Wait for compound to dry, then wash glass clean with water to make a slurry and wipe off.
6. Remove polishing pad from applicator, then wash and dry for future use.
Just spray and wipe to clear away fingerprints, smudges, and dust. Not only that, but Wash Mist PLUS destroys bacteria and viruses, leaving an antimicrobial coating that lasts for ca. 1 week, and reduces the amount of dust absorbed and released by interior fabrics. Note: not guaranteed to remove 100% of all microorganisms
Directions
When cleaning inside window, seat and floor mat:
1. Remove stopper before use.
2. Directly spray onto area and wipe off with dry clean towel. * Allow liquid to soak, then wipe off * Wipe off with water if use for cleaning child seat.
When cleaning dash board, handles, trims, plastic and LCD screen
Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.
Direction
1. Remove dust and dirt from glass with water, dry off any water remaining on surface.
2. Shake bottle well.
3. Pour liquid onto white side of included pad, begin to polish surface of glass.
pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.
Direction
1. Wash off sand, mud or dust prior to spraying.
2. Shake bottle well approx. 20 times, and turn trigger "ON".
3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.
4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.
* When spray over brake disc, it reacts and changes colour.
Rinse away immediately, if left on too long, may cause bad effects for brake disc.
5. Wipe off with clean towel.
Carry out brake test with low gear 2-3 times after cleaning.
* This product is formulated for wheel.
If use for car body, carefully rinse off with water afterwards.
SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.
Direction
1. Wash car, removing sand and dust from the body of vehicle.
2. Knead clay bar by hand until it's soft and flat.
3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.
Direction
1. Wash car to remove sand or dust.
2. Knead clay bar by hand until it's soft and flat.
3. Rub lightly on car surface and wet area being cleaned.
4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.
Note: Always let the clay bar do the work never add pressure on the surface. Always lubricate with water or shampoo water when using clay bar on surface.
Gel type spray glass cleaner lets you clean the glass easily without any liquid or water droplets leaving residue. The cleaning components are held in the gel, giving time to penetrate dirt and increase the effectiveness of cleaning stubborn dirt, such as bird droppings. Also suitable for use on mirrors, unpainted plastic, and rubber parts.
Direction
1. Turn the spray nozzle to “ON”.
2. Without shaking, spray onto the glass surface from 15 – 20cm away, then immediately wipe around the glass with a clean, dry towel.
3. Wipe up the dirt, changing to a fresh surface of the towel when necessary.
*If some residue remains on the glass, wipe again with a clean towel.
Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!
✔ Oil, Polish residue and fillers remover ✔ Prep item before applying wax / coating ✔ Replaces IPA wipe down ✔ Improves the adhesion of the surface protective coating ✔ Safe for paint
Direction
1. Shake bottle well
2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth
3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.
Neutral Shampoo Creamy Type Quick Rinsing + Compound in
High performance pH neutral shampoo removes stubborn dirt in a flash. Will not attract dirt even if the soap dries up during wash. Powerful wash that regains paint clarity. Ultra-fine cleaner particles clean without damaging the paint. Removes minor water spots in one wash.
Direction
1. Remove sand and dust from car with water.
2. Shake bottle well with cap on.
3. Pour 1 or 2 coin size drops of shampoo directly onto a damp sponge, create lather by rubbing sponge.
4. Clean vehicle with sponge.
5. Rinse well with water until all bubbles are gone.
6. Wipe off all water drops remaining on surface with a clean or absorption towel. If water drops remain on surface, it may cause spots or stains.
Neutral shampoo which doesn’t damage your car's coated surface. Formulated for maintaining professional or wax-coated vehicles. Included sponge will create bubbles and lather. Product contains NO synthetic cleaning components and abrasive compounds. Natural ingredient, eco-friendly and compatible with ALL colours.
Direction
1. Remove dust and dirt with water.
2. Dilute the liquid 1 cap/ 1L water and apply to included sponge.
3. Wash car gently with sufficient bubbles.
4. Rinse and wipe off remaining water drops with a clean towel.
Powerful alkaline cleaner designed to remove tar, pitch and stubborn oily contamination from vehicle bodywork, wheels and tyres.
Effectively removes degraded coatings, water stains, insects and bird droppings without the need for abrasive compound. Orange oil assists in breaking down stubborn insect and bird dropping residue.
Also highly effective as a degreasing cleaner and can be used to prepare surfaces before applying waxes, sealants or coatings.
Direction
1. Wash off sand, mud or dust prior to spraying.
2. Turn the nozzle to the "ON" position and spray directly onto the surface.
3. Allow the product to dwell for approximately 30 seconds, then gently agitate with a cloth or brush.
If contamination remains, repeat the process.
4. Thoroughly rinse the treated surface with water and dry with a clean towel.
* Ensure all product is completely rinsed away. Residue left on the surface may cause damage.
5. Rinse the nozzle with water after use.
* It is recommended to work panel by panel.
When used on wheels, carry out a brake test at low speed after cleaning.
* Tar Exterminator will strip coatings, waxes and other existing protection from treated surfaces. Reapply suitable protection after use to restore shine and water repellency.
Product is a spray on mousse that helps reduce condensation on the windows in cold temperatures. All you need to do is spray on leave it for 3 mins and buff it off! The spray can comes in size of 180ml which is enough to last approximately 8-10 windscreen, durability is up to a month.
Direction
1. Clean glass surface prior to application
2. Make sure surface is dry prior to application, you can spray product directly to the glass or on a microfiber cloth
3. Spread evenly, the glass should be full of foam solution, let it on for 3-5 mins
4. Wipe off with another cloth! If necessary you can use paper towel to dry the area.
*Warning do not put near open flames, keep clear away from children
Remove fog-causing dirt and leave a durable anti-fog coating to prevent fogging. Easy to use, cleaning and coating are completed in one step. Compatible with UV and IR blocking coatings!
Direction
1. Turn the spray nozzle to (ON).
2. Without shaking, spray onto the glass surface from 15-20 cm away, then immediately wipe around the glass with a clean, dry towel.
3. Wipe up the dirt, changing to a fresh surface of the towel when necessary. Finally wipe up with a dry surface.
* If some residue remains on the glass, wipe again with a clean towel.
Interior glass cleaner for professionals. Quickly clear smudges and smears with no dripping, using this gel-type cleaner. Additionally, it adds an anti-fog effect!
Just spray on and wipe off to remove dead bugs, tar, and other oily dirt. It really is that so simple! It also creates a temporary anti-fouling coating to prevent adhesion of dirt.
Direction
* Use on a washed and dried vehicle.
1. Spray on the dirty area from a distance of 20-30 cm.
This non-abrasive deep clean can dissolve unsightly residues on wheels. The foam is easy to apply, and does not drip off, allowing the chemical components to work on loosening and lifting the dirt. The included sponge makes it easy to agitate dirt out from tight spaces. Suitable for aluminium and steel wheels.
Direction
1. First use water to remove what dust and dirt can be rinsed away.
2. Shake well and spray over the entire wheel. If the trigger is locked, turn the nozzle to open.
3. Let sit for 2-3 minutes, and then agitate with the provided sponge to lift dirt from the wheel surface.
4. Rinse thoroughly with water to remove all cleaner and dirt.
Multi-purpose interior cleaner. Can be used on all surface (fabric, trims, dash, and windows. Super quick drying, leaves no additional finish. Eliminates odour and leaves a refreshing grape fruit scent. Contains ethanol for antibacterial clean.
Directions
When cleaning inside window, seat and floor mat:
1. Directly spray onto area and wipe off with dry clean towel. * Allow liquid to soak, then wipe off * Wipe off with water if use for cleaning child seat.
When cleaning dash board, handles, trims, plastic and LCD screen
SOFT99 Leather Cleaner & Conditioner not only safely and efficiently cleans leather without risk of drying or degradation, but also restores and protects leather's natural gloss and sheen, without feeling greasy or sticky.
Direction
To apply, simply spray onto the surface and wipe around with a microfiber cloth.
Allow to dry about 20 minutes after wiping
For perforated leather, apply indirectly by spraying onto the microfiber towel first.
Easily remove dirt and stains from automobile leather with the easy-grip bottle and integrated applicator. The MVB (Microvelvet Brush) uses ultrafine fibres to work in the grain of the leather to properly remove contamination without damaging the surface. Specialised surfactants remove stains including from denim, etc. While also containing the leather-conditioning carnauba wax, a non-slip effect has also been achieved. Also suitable for PVC and urethane synthetic leathers.
Direction
Note: Before use, test on an inconspicuous area.
1. Grip firmly and open cap.
2. Squeeze the bottle regularly to release liquid, and spread around the surface, while gently scrubbing.
3. Wipe up with a dry towel.
Note: to release more liquid, squeeze the bottle with the brush face down towards the seat, or for vertical surfaces, with the narrow end pointed downwards.
Not only cleans fabric seat but also gets rid of bad odours. Antibacterial effect prevents moulds or ticks from occurring, leaving a fresh mint scent behind. Can easily remove dirt, tar, stains or sebum from fabric seats. Included brush used for agitation to remove dirt in fabric. Organic solvent is NOT included, so it is very friendly to people and fabrics.
Direction
1. Turn nozzle to <MIST>.
2. Spray from a distance of approximately 15-20cm from fabric seats or mats.
3. Use included brush to agitate, area sprayed will bubble.
4. Wipe off the bubble and dirt with a clean towel before surface gets dry.
Special cleaning mousse formulated to remove dirt without damaging leather seat. Contains no scent, which does not leave any bad odour after cleaning. Blended with Vitamin E to moisturise and prevent leather seat from deteriorating.
Direction
1. Shake can well.
2. Spray mousse on a soft cloth and rub in into leather.
Spot stain remover kit for fabric seat which is effective for removing stubborn stain. Three simple procedure "Wash"→"Rinse"→"Absorb" can remove stain using our exclusive liquid and HPVA sponge. Can remove up to 30 fifty cent coin size stain. * HPVA=Hexagonal Polyvinyl Alcohol
Directions
1. Soak sponge in water and squeeze allowing sponge to become moist.
2. Shake bottle well and apply 5 drops of liquid onto sponge.
3. Press and tap sponge on stained area. Cleaning liquid will react with stain and loosen it from the fabric fibres.
4. Rinse sponge.
5. Remove stain from fabric seat by using hexagonal side of sponge to absorb. Rotate each side continuously.
6. Rinse sponge and use flat clean side to absorb remaining excess liquid.
PROSPEC dirt-repellent coating for fabric (antibacterial anti-odor) 4L
A fluorine-based dirt-repellent coating that does not allow the penetration of oil-based stains such as juice, coffee, mayonnaise, sauce, sweat, etc. into the fibers. The coating forms a continuous layer, which means dirt does not accumulate and it is very durable. An aqueous type product that does not use petroleum solvents.
Additionally, the incorporated organic antibacterial agents improve hygiene and prevent smells.
Abrasives for correcting and finishing automobile paint
Formulated for efficient correction (scratch removal), polishing, and high-gloss finishing of automobile paint. Suitable for machine polish only
Cutting Compound 300ml Remove scratches, orange peel, and sandpaper marks with Cutting Compound Wool buff pad @ 1800rpm
Polishing Compound 300ml Remove marks from Cutting and bring to a gloss with Polishing CompoundSponge/Euro foam buff pad @ 1500rpm (if sandpaper marks remain, use wool)
Finishing Compound 300ml If desired, bring paintwork up to perfection with clear gloss then finish with Finishing Compound Sponge/Euro 'finishing' foam buff pad @ 1300rpm
Excellent properties with results:
Suitable for all types of automobile paint
Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
New anti-clogging, low dust formula improves working conditions
Can be used as a two- or three-step process, as needed
Contain no silicone, gloss-enhancers, or any other unnecessary additives
Remove marks from Cutting and bring to a gloss with Polishing Compound
✔ Suitable for all types of automobile paint ✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring ✔ New anti-clogging, low dust formula improves working conditions ✔ Can be used as a two- or three-step process, as needed ✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives
Recommended Pad & Speed
Sponge/Euro foam buff pad @ 1500rpm (if sandpaper marks remain, use wool)
This versatile, full-spectrum compound for professionals is designed for efficient correction (scratch removal),polishing, and high-gloss finishing of automobile paint. It is optimized for machine polishing,but may also be used by hand.
