Cleaners & Surface Prep

Content - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Direction

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 400ml

Features

This non-abrasive deep clean can dissolve unsightly residues on wheels. The foam is easy to apply, and does not drip off, allowing the chemical components to work on loosening and lifting the dirt. The included sponge makes it easy to agitate dirt out from tight spaces. Suitable for aluminium and steel wheels.

Direction

1. First use water to remove what dust and dirt can be rinsed away.

2. Shake well and spray over the entire wheel. If the trigger is locked, turn the nozzle to open.

3. Let sit for 2-3 minutes, and then agitate with the provided sponge to lift dirt from the wheel surface.

4. Rinse thoroughly with water to remove all cleaner and dirt.

5. Wipe off remaining water.

6. Check brakes at low speed before driving.

Contents - Cleaner (120mL) x 1bottle, Brush x 1pc, Cup x 1pc, Gloves x 2pcs

Features

This is acid type wheel cleaner, can dissolve burned iron powder and brake dust which cannot remove by conventional wheel cleaner with easy procedure.
Strong acid cleaner dissolves heavy iron powder, which stuck against wheel, without damaged paint surface.

Direction

1. Remove dirt or oil by car shampoo and wipe off thoroughly.

2. Be sure that wheel is cool and confirm the area where iron powder is accumulated.

3. Take moderate amount of solution into attached cup, and start applying accumulated area with brush.

4. Let sit 10 minutes, buff off with clean towel. In case of difficultly wiping off once, repeat procedure 3 and 4.

* Application is up to 3 times.

5. Afterwards remove residue by rubbing with water.

* If rinsing is not enough, wheel might discolour, blushing and cause stain.

Contents - 4000ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Direction

1. Wash off sand, mud or dust prior to spraying.

2. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

3. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

4. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 800ml

Features

Brown staining on wheels and tyres really ruins the whole look of a vehicle. This newly-developed spray reacts with contaminants, even when embedded in the rubber, dissolving them to make it easy to simply rinse away the dirt. The sophisticated formula is gentle to wheel and tyre, but extremely powerful against oily grime and tar. Specialised grip makes for easy use, with generous contents that can treat approx. 20 wheels and tires.

Direction

1. Rinse surface with water to remove any dust or dirt.

2. Set nozzle to the ON position, and spray over entire surface without opening the white flap. Use around 40 shots for an average wheel.

3. Wait around 30 seconds for reaction, before scrubbing with a brush.

4. Ensure to rinse thoroughly with water, and dry with a towel. Failure to remove all product may damage surfaces.

5. Rinse nozzle with water after use.

Note: Test brakes at low speed after use. We recommend DiGloss Kamitoré series for effective tyre-cleaning tools. After use, protect your tyres with DiGloss Black Devil Tire Wax!